mrsmoky
Fire Starter
Original poster
- Apr 21, 2012
- 66
- 10
- Oceanside, New York. (Long Island)
- Apr 1, 2013
- #1
Hey guys thanks in advance.
My Masterbuilt 40 was on an extension cord plugged into a power strip and an iron was used in the power strip and my smoker turned off. Now it wont turn on. Also it had to be stored outside and its been a rainy season I'm concerned about mold and I cannot turn it on to kill any mold in case there is any. Any help is greatly appreciated to get my smoker back up and running Thank you!
chef jimmyj
Gone but not forgotten. RIP
OTBS Member
SMF Premier Member
★ Lifetime Premier ★
- May 12, 2011
- 22,172
- 7,150
- Apr 1, 2013
- #2
Have you tried it in a different Outlet and with a different Extension Cord? The heating coil in the MES and the Iron most likely tripped the breaker to the Outlet it was plugged into or the the breaker on the power strip...JJ
Last edited:
mrsmoky
Fire Starter
Original poster
Thread starter
- Apr 21, 2012
- 66
- 10
- Oceanside, New York. (Long Island)
- Apr 1, 2013
- #3
I plugged it in directly to another outlet and nothing...
mrsmoky
Fire Starter
Original poster
Thread starter
- Apr 21, 2012
- 66
- 10
- Oceanside, New York. (Long Island)
- Apr 1, 2013
- #4
It's happened before and I switched the breaker which turned it back on....now that doesnt seem to be working..
chef jimmyj
Gone but not forgotten. RIP
OTBS Member
SMF Premier Member
★ Lifetime Premier ★
- May 12, 2011
- 22,172
- 7,150
- Apr 1, 2013
- #5
I am not aware of any breaker or fuse in the MES and it does not sound like a power surge hit the Smoker. This may sound silly but did you verify the second outlet works with something else so you can narrow the problem down to just the MES. There is pretty much only the Electronics that could have been affected. If there is power to the outlet, I would contact Masterbuilt to see what they say...JJ
mrsmoky
Fire Starter
Original poster
Thread starter
- Apr 21, 2012
- 66
- 10
- Oceanside, New York. (Long Island)
- Apr 1, 2013
- #6
I will make sure to be as thorough as possible and then take it from there to contact Masterbuilt if needed. Thanks!
darock159
Newbie
- Mar 2, 2013
- 14
- 11
- Kansas City Area (Olathe KS)
- Apr 9, 2013
- #7
Have you tried the remote. I had the control unit go bad on me (it got water in it i think) and none of the buttons on the smoker itself would work. However, when I tried the remote I could get it to work properly. Masterbuilt sent me a new control unit that fixed the problem, but I could still smoke a little while I waited for it to arrive. Hope you get it fixed.
Reactions:
kwats4
mrsmoky
Fire Starter
Original poster
Thread starter
- Apr 21, 2012
- 66
- 10
- Oceanside, New York. (Long Island)
- Apr 22, 2013
- #8
Thanks, yeah I tried a bunch of stuff Just got off the phone with Masterbuilt they're sending me a new control unit and heating element. So lesson learned but there will be smoked meat this summer!!! Cheers and Thanks!
mrsmoky
Fire Starter
Original poster
Thread starter
- Apr 21, 2012
- 66
- 10
- Oceanside, New York. (Long Island)
- May 4, 2013
- #9
Ok so I got a new heating element and control panel from Masterbuilt. Here's the thing. I put on the new control panel and it still didn't turn on. Do I need to put in th new heating element to get power? I dont have time today to put in the heating element just wanted to see if the thing would turn on. Thanks,
firedude212
Newbie
- Oct 16, 2015
- 2
- 10
- Oct 16, 2015
- #10
Hi I know it has been a couple years that you had this problem but I was wondering if the heating element fixed the problem? I had a little fire in Mine :) and now it won't power on . I got a new controler but it didn't work either.
Thanks for your help
walta
Smoke Blower
- Jul 20, 2015
- 88
- 17
- St Louis MO
- Oct 16, 2015
- #11
Firedude212
Does the display light up on your control panel?
Have you opened the back and inspected the terminal of the heater?
Walta
firedude212
Newbie
- Oct 16, 2015
- 2
- 10
- Oct 17, 2015
- #12
No the lights do not light up on the control panel
I have not yet taken the back cover off yet I had lower model Masterbuilt before this replacement one and had the burner go out several time however the unit would still turn on just not heat up.
I am going to take it apart later today and see what I can tell
Thanks Justin
walta
Smoke Blower
- Jul 20, 2015
- 88
- 17
- St Louis MO
- Oct 17, 2015
- #13
Firedude212
Is your outlet GFCI protected?
Please plug something else in your outlet and see if it is working.
Walta
bryantom
Fire Starter
- Mar 6, 2011
- 32
- 10
- Central Texas
- Nov 17, 2018
- #15
Where are we at with this? I went outside today to turn on my Masterbuilt and it wont turn on. when i plug it in i get the beep from the control panel but cant get it to turn on
dr k
Master of the Pit
OTBS Member
★ Lifetime Premier ★
- Mar 22, 2013
- 3,183
- 997
- Peoria, IL
- Nov 17, 2018
- #16
bryantom said:
Where are we at with this? I went outside today to turn on my Masterbuilt and it wont turn on. when i plug it in i get the beep from the control panel but cant get it to turn on
The post before yours is over three years old. You might want to start a new thread.
yzfr1girl
Newbie
- Jan 15, 2016
- 3
- 10
- Nov 17, 2018
- #17
bryantom said:
Where are we at with this? I went outside today to turn on my Masterbuilt and it wont turn on. when i plug it in i get the beep from the control panel but cant get it to turn on
We had that happen w/ours. It would turn on, the trip the breaker. I thought it was done but, turns out its just the element in the back. I called MB and they sent me a new one at no charge..apparently it happens often. HTH
You must log in or register to reply here.