10x20 2 Stall Horse Barn Plans | MyOutdoorPlans (2024)

This step by step diy project is about 10×20 2 stall horse barn plans. I have designed this double stall horse barn, so you can shelter your horses properly. This post frame horse barn is easy to build and extremely durable. Make sure you check the local codes and make adjustments to the plans, if required. Take a look over the rest of mywoodworking plans, if you want to get more building inspiration.

When buying the lumber, you should select the planks with great care, making sure they are straight and without any visible flaws (cracks, knots, twists, decay). Investing in cedar or other weather resistant lumber is a good idea, as it will pay off on the long run. Use a spirit level to plumb and align the components, before inserting the galvanized screws, otherwise the project won’t have a symmetrical look. See all my Premium Plans HERE.

Projects made from these plans

10×20 2 Stall Horse Barn Plans

Cut & Shopping Lists

• A– 3 pieces of 4×4 lumber – 127 1/2″ long, 3 pieces – 135 1/2″ longPOSTS
• B– 3pieces of 4×4 lumber– 113″ long, 3 pieces – 114 3/4″ longSKIDS
• C – 5 piece of 4×4 lumber – 88″ long, 4 pieces – 96″ longPOSTS
• D– 2 pieces of 2×8 lumber – 240″ longBEAMS
• E– 12 pieces of 2×4 lumber – 55 3/4″ long, 12 pieces – 54 3/4″ long, 12 pieces – 30″ long, 2 pieces – 68 1/2″ long, 22 pieces – 54 3/4″ long, 2 pieces of 2×6 lumber – 48″ long, 2 pieces – 36″ long, 4 pieces of 2×8 lumber – 48″ longSUPPORTS

• 6 pieces of 4×4 lumber – 12′
• 9 pieces of 4×4 lumber – 8′
• 7 pieces of 4×4 lumber – 10′
• 2 pieces of 2×8 lumber – 20′
• 15 pieces of 2×4 lumber – 10′
• 2 pieces of 2×8 lumber – 8′
• 3 1/2″ lag screws
• 2 1/2″ screws, 3 1/2″ screws
• framing nails
• wood filler,wood glue, stain/paint

Tools

Hammer, Tape measure, Framing square, Level

Miter saw, Drill machinery, Screwdriver, Sander

Safety Gloves, Safety Glasses

Time

Oneweek

Related

• PART 1: 10×20 2 Stall Horse Barn Plans
• PART 2: 10×20 2 Stall Horse Barn Roof Plans
• PART 3: 10×20 2 Stall Horse Barn Door Plans

How to build a 10×20 horse barn with tack room

The first step of the project is to build the corner posts. As you can see in the diagram, you need to make a notch to the top of the 4×4 posts. Make parallel cuts to the top of the posts and then remove the excess with a chisel. You need to set the posts 3′ in concrete.

The next step of the project is to layout the location of the posts. Use batter boards and string to mark the location for the corner posts. Apply the 3-4-5 rule to the corners and then dig 3′ deep holes into the ground. Plumb the posts with a spirit level and then secure them into place temporarily with braces. Fill the holes with concrete and let it dry out for a few hours.

Fit the 4×4 pressure treated skids between the posts. Align the edges with attention and make sure the corners are square. Drill pilot holes and insert 3 1/2″ screws to lock them to the vertical posts. Use corner brackets as well.

Use 4×4 lumber for the intermediary posts. As you can see in the diagram, you need to make notches to the top of several posts.

Fit the posts to the structure of the shed, as shown in the diagram. Make sure the corners are square and plumb them with a spirit level. Use screws to lock the posts to the skids.

Fit the 2×8 beams to the front and back of the shed. Align the edges with attention and then lock the beams to the posts with 3 1/2″ lag screws. Use a spirit level to check if the beams are horizontal.

Fit the supports for the kickboards to the back of the shed. Use 2×4 lumber for the supports. Drill pocket holes at both ends of the supports and insert 2 1/2″ screws to lock them to the posts.

Fit the 2×4 supports to the front of the shed, as well. Use a carpentry square to make sure the corners are right-angled.

Use 2×8 lumber and 1/2″ plywood for the double headers. Toenail the headers to the posts, as shown in the diagram.

Fit the 2×4 supports to the sides of the shed. Drill pocket holes at both ends and then insert 2 1/2″ screws to lock them to the vertical posts.

After attaching the supports, the frame of the shed should look as in the image.

Take a look over PART 2 and PART 3 of the 2 stall horse barn project, to see free plans for the saltbox and for the double doors.

I have lots of other shed projects on the site so I recommend you to browse through all alternatives before starting the building project. See all my shed projects HERE.

If you want to get PREMIUM PLANS for this project, in a PDF format, please press GET PDF PLANS button bellow. Thank you for the support.

This woodworking project was about 10×20 2 stall horse barn plans free.If you want to see more outdoor plans, check out the rest of our step by step projects and follow the instructions to obtain a professional result.

EXPLORE MORE IDEAS FOR:

Ovidiu

I've been a designer and a woodworker since I first developed consciousness.